CAT CPI1000 Power Inverter Instruction Manual
Download PDF user manual for Caterpillar CAT CPI1000 1000-Watt Power Inverter with USB Charging Ports (EN|ES) 28 pages RD072815 2015 zip
Description
This PDF instruction manual is for the CAT CPI1000 Power Inverter.
About the Item
CAT CPI1000 1000-Watt Power Inverter with USB Charging Ports
This inverter is an electronic device that converts low voltage DC (direct current) electricity from a battery to 120 volts AC (alternating current) household power.
Read and understand this instruction manual before using this unit. Save this manual for future reference.
DOCUMENT(S) AVAILABLE
(PDF) INSTRUCTION MANUAL / MANUAL DE INSTRUCCIONES
Available Languages
ENGLISH (EN) | ESPAÑOL (ES)
SUMMARY OF CONTENTS
SAFETY GUIDELINES / DEFINITIONS
IMPORTANT SAFETY INSTRUCTIONS
– General safety warnings and instructions for all inverters
– Extension cords. Minimum Gauge for Cord Sets.
INTRODUCTION
This power inverter is configured to supply continuous power in the form of two 120 volt AC outlets and two 5 volt USB charging ports to run most household or electronic appliances.
– Controls and Functions
– Names of parts, indicators, ports
HOW THIS INVERTER WORKS
– Power Inverter Output Waveform. The AC output waveform of this inverter is known as a modified sine wave.
– Incompatible Products
PROTECTIVE FEATURES
The inverter monitors the following conditions:
– Low Battery Voltage
– Input Voltage Too High
– Thermal Shutdown Protection
– Overload/Short Circuit Protection
OPERATING TIPS
INSTALLATION
– Metal Plate Installation
– Mounting the Inverter
OPERATING INSTRUCTIONS
– The Power Inverter must be connected only to batteries with a nominal output voltage of 12 volts.
– Connection to Power Source
– Connecting to a power source using the DC accessory outlet plug (up to 100W only)
– How to turn the inverter on.
Notes: If the power/fault LED flashes red, the unit emits three beeps every five seconds, the 100W LED indicator does not light and the AC outlets and USB charging ports shut down, a fault condition has occurred. Refer to the Protective Features section and the Troubleshooting section of this manual.
– Connecting to a power source using the provided battery clips with slide-in connectors
– Direct hardwiring to power source (optional connection method)
– Important cable information
– Connection To Load
– Rated Versus Actual Current Draw of Equipment
– Inductive loads, i.e. power tools
READING THE POWER/FAULT LED
The power/fault LED is located inside the On/Off Button. Press the On/Off Button once to turn the unit on.
The Power/Fault LED lights or flashes in one of three colors, indicating the following:
– Blue: The inverter is properly connected to a functioning DC power source and is operating at full voltage; the AC outlets and USB charging ports are ready to use.
– Orange: The inverter is properly connected to a functioning DC power source and is operating at partial voltage. The AC and USB outlets are active; however this indicates the inverter will shut down soon as the power source voltage is low.
– Red (flashing): A fault has accured. The unit emits three beeps every five seconds, and the AC and USB outlets are automatically shut down. Refer to the Protective Features Seconds and the Troubleshooting Section of this Instruction Manual. Press the On/Off Button to turn the inverter off, correct the fault and then press the On/Off Button again to turn the inverter back on.
– Operation of the 120 Volts AC Outlets
– Operation of the USB Charging Ports
CARE AND MAINTENANCE
– Storage
– Fuse Replacement
TROUBLESHOOTING
Common Audio/Visual Problems:
– Buzzing sound in audio systems
– Television interference
Common Power Output Problems:
– Input voltage below 10.5 volts
– Equipment being operated draws too much power
– Inverter is thermal shutdown condition
– AC output is shorted
ACCESSORIES
SERVICE INFORMATION
WARRANTY
SPECIFICATIONS
– Maximum Continuous Power: 1000 watts
– Input Voltage: 12 volts DC, 100A
– Output Voltage: Approx. 110-125 volts AC RMS, 60 Hz
– Wave Form: Modified Sine Wave (MSW)
– Output Connection: North American Standard Receptacles
– USB Output: 2 x 5 V DC / 2A total
– DC plug fuse: 12A
Why download the Manual?
This instruction manual provides all the information from CAT / Caterpillar about the CPI1000 power inverter, as detailed in the table of contents. Reading it completely will address most questions you might have. You can download and save it for offline use, including viewing it on your device or printing it for your convenience if you prefer a paper version.
How to download the Manual?
Download it by clicking the button below
Helped you out?
Glad to hear that. It would be awesome if you could . . .