Motorola MOTOTRBO SLR8000 Base Station/Repeater Manual

Description

This PDF user and service manual is for the Motorola MOTOTRBO SLR8000 Base Station/Repeater.

About the Item

Motorola MOTOTRBO SLR8000 Base Station/Repeater

MN002299A01-AA
MN002253A01-AB

The Motorola SLR 8000 Base Station/Repeater provides a modular, flexible analog and digital station designed for today’s communication systems and for the future

The SLR 8000 can either be configured as a stand-alone base station/repeater or as a base station/repeater connected to a back-end network, as in the case of operating in IP Site Connect mode. As a base station/repeater, it listens on one uplink frequency, and then re-transmits on a downlink frequency, thus providing the RF interface to the field subscribers. When configured for analog station operation, the repeater or base station is designed to operate with most existing analog systems, which enables a smooth migration to the MOTOTRBO system.
When configured for digital operation, the base station/repeater offers additional services. The digital base station/repeater operates in TDMA mode, which essentially divides one channel into two virtual channels using time slots; therefore the user capacity is doubled. The base station/repeater utilizes embedded signaling to inform the field radios of the busy/idle status of each channel (time slot), the type of traffic, and even the source and destination information.

This manual covers all versions of the MOTOTRBO SLR 8000 Base Station/Repeater, unless otherwise specified. It includes all the information necessary to maintain peak product performance and maximum working time, using levels 1 and 2 maintenance procedures.
For safe installation, operation, service and repair of this equipment, follow the safety precautions and instructions described below.

(PDF) BASIC SERVICE AND INSTALLATION MANUAL (ENGLISH)

SUMMARY OF CONTENTS

– Foreword
– General Safety and Installation Standards and Guidelines
– Part 68 Information
– MOTOTRBO SLR 8000 Base Station/Repeater Supplemental Safety and Installation Requirements
– Environmental Information
– Document History
CHAPTER 1. SLR 8000 Base Station/Repeater
1.1 Notations Used in This Manual
1.2 Description
1.3 Operating Features
1.4 Frequency Ranges and Power Levels
1.5 Specifications
1.6 Theory of Operation
1.7 Basic Base Station/Repeater Level Troubleshooting – RDAC and LEDs
1.8 Model Chart: VHF High Power, UHF1 High Power
CHAPTER 2. SLR 8000 Satellite Receiver
2.1 Description
2.2 Operating Features
2.3 Frequency Ranges
2.4 Specifications
2.5 Configuration
2.6 Basic Station Level Troubleshooting – RDAC and LEDs
2.7 Satellite Receiver System (Analog)
CHAPTER 3. SLR 8000 Modem
3.1 Description: General Description, Input and Output Connections, Frequency Bands
3.2 Receiver Subsystem
3.3 Transmitter Exciter Subsystem
3.4 Station Control Subsystem: High Stability Reference Block, Audio
3.5 Station Control Interface: Front Panel Interface Connector, Rear Panel Connections, Power Amplifier Interface Connector, Power Supply Interface Connector, Expansion Board Interface Connector, Chassis ID Interface Connector, Wireline/ Aux Board Interface Connector
CHAPTER 4. SLR 8000 Power Amplifier
4.1 Description
4.2 General Description
4.3 Input and Output Connections
4.4 Frequency Ranges
4.5 Specifications
4.6 Modem Interface
CHAPTER 5. SLR 8000 Power Supply
5.1 Description
5.2 Specifications
5.3 Power Supply Interface: Power Source Inputs/Outputs/Digital Interface/Output Cable Signaling
CHAPTER 6. SLR 8000 Front Panel
6.1 Description
6.2 Input and Output Connections
6.3 Interfaces
6.3.1 Modem Interface
6.3.2 User/ Service Interface: USB, LED Indicators, Speaker Volume Adjust Buttons, Microphone
CHAPTER 7. SLR 8000 Back Panel
7.1 Description
7.2 Back Panel Interfaces: AC Power Inlet, DC Power Inlet / DC Charger Outlet, Option 1/GNSS, Option 2/WLAN, USB, Ethernet 1, Ethernet 2, Auxiliary (Aux), Frequency Reference, Receiver RF, Transmitter RF, Bonding Ground Connection, Wireline 1 (WL1), Wireline 2 (WL2), GPIO 1, GPIO 2, GPIO 3, RF Antenna Relay, P-TEMP
CHAPTER 8. SLR 8000 Test Equipment And Service Aids
8.1 Recommended Test Equipment
8.2 Service Aids
Chapter 9. SLR 8000 Performance Check or Testing
9.1 General
9.2 Transmitter Testing: Test Equipment, Verifying Transmitter Circuitry Procedure,
9.3 Receiver Testing: Required Test Equipment, Verifying Receiver Circuitry Procedure
CHAPTER 10. SLR 8000 Programming and Tuning
10.1 Introduction
10.2 Customer Programming Software Setup
10.3 Reference Oscillator Alignment: Tuning Procedure
10.4 Base Station/Repeater Tuning Setup
10.5 Rx Audio Level Set: Tuning Procedure
10.6 Tx Audio Level Set: Tuning Procedure
10.7 Modulation Limit Alignment: Tuning Procedure, Verification
10.8 Tuning Setup (Wireline): Wireline Receive Level Tuning, Tuning Procedure, Wireline Rx Equalization – 2800 Hz Tuning, Wireline Rx Equalization – 400 Hz Tuning, Wireline Transmit Level Tuning, Wireline Squelch Level Tuning, Wireline Status Tone Level Tuning (Analog Voting)
CHAPTER 11. SLR 8000 Maintenance and Disassembly/Reassembly
11.1 Introduction
11.2 Routine Maintenance
11.3 Preventive Maintenance: Inspection, Cleaning Procedures
11.4 Safe Handling of CMOS and LDMOS Devices
11.5 Disassembly of Optional Equipment: External Circulator Tray Disassembly/Reassembly
11.6 Disassembly: Detailed, Cosmetic Cover Disassembly, Front Bezel Disassembly, Faceplate Disassembly, Faceplate Disassembly– Detailed, Fan Module Disassembly, Bezel Clip Disassembly, Cable Disassembly, Power Supply Module Disassembly, Modem Module Disassembly, Power Amplifier Disassembly, Back Panel Disassembly
11.7 Reassembly: Reassembly – Detailed, Bottom Cover Installation, Power Amplifier Module Installation, Modem Module Installation, Power Supply Installation, Back Panel Installation, OPTIONAL – Antenna Relay Installation, Receive Cable Installation, Faceplate Installation, Cable Installation, Bezel Clip Installation, Fan Installation, Option Plug Installation, Top Cover Installation, Front Bezel Installation
11.8 Exploded Mechanical View
11.9 Parts List
11.10 Torque Charts
CHAPTER 12. SLR 8000 Installation
12.1 Pre-Installation Considerations: Installation Overview, Site Environmental Conditions, Equipment Ventilation, AC and DC Input Power Requirements, Equipment Mounting Methods, Recommended Tools and Equipment, Equipment Unpacking and Inspection
12.2 Mechanical Installation: Equipment Unpacking and Inspection, Mounting Procedures, Transferring Equipment from Shipping Container to Rack or Cabinet, Installing Racks, Installing Cabinets
12.3 Post Installation Checklist: Applying Power, Verifying Proper Operation, Front Panel LEDs, Copying the Repeater Codeplug Data to a Computer
12.4 Installing Base Station/Repeater Hardware Options: General Bonding and Grounding Requirements, General Cabling Requirements
CHAPTER 13. SLR 8000 Wireline
13.1 Description: Input and Output Connections
13.2 Specifications
13.3 Board Configuration: DC Remote Jumper Configuration, E&M Jumper Configuration, CPS Configuration, Choosing a Remote Control Mode, Other Wireline Configuration Options
13.4 Tone Remote Control
13.5 DC Remote Control
13.6 Voting
CHAPTER 14. SLR 8000 Radio Frequency Distribution System (RFDS) Equipment
14.1 Description: Base Station/Repeater Preselectors, Duplexer, External Dual Circulator Tray, Antenna Relay
14.2 Specifications: Base Station/Repeater Preselectors, Duplexer, External Dual Circulator Tray, Antenna Relay
14.3 Field Tuning Procedures: Base Station/Repeater Preselectors, Internal Preselector Tuning Procedure (Preferred Method), Test Equipment, Equipment Setup, Tuning Connections, Internal Preselector Tuning Procedure (Alternate Method), Test Equipment, Equipment Setup, Tuning Connections, Duplexer Tuning Procedure (with basic instruments), Tuning the LO side, Tuning the HI side, Fine Tuning the Duplexer
APPENDIX A. Accessories: Cables, Documentation, Duplexer, Mounting, Preselectors, Service Kits, Service Parts, Service Tools, Microphone, Miscellaneous
APPENDIX B. EMEA Regional Warranty, Service and Technical Support
APPENDIX C. SLR 8000 Third Party Controllers
C.1 Overview
C.2 Community Repeater Panel
C.3 Phone Patch
C.4 Tone Remote Adapter
C.5 Trunking Controllers
APPENDIX D. Audio Enhancement
APPENDIX E. MOTOTRBO Base Station/Repeater – EME ASSESSMENT
GLOSSARY OF TERMS AND ACRONYMS
LIST OF FIGURES
LIST OF TABLES

(PDF) MOTOTRBO SLR8000 Series Base Station Repeater QUICK START GUIDE (MN002302A01-AA) 2016

(PDF) MOTOTRBO SLR 8000 Repeater Product DATA SHEET (2018)

(PDF) MOTOTRBO SYSTEMS AT A GLANCE BROCHURE

Why download the Manual?

This basic service and installation manual provides all the information from Motorola Solutions about the MOTOTRBO SLR8000 Base Station/Repeater, as detailed in the table of contents. Reading it completely will address most questions you might have. You can download and save it for offline use, including viewing it on your device or printing it for your convenience if you prefer a paper version.

How to download the Manual?

Download it by clicking the button below

Download file

Helped you out?
Glad to hear that. It would be awesome if you could . . .