NOCO GENPRO10X2 2-Bank 20A On-Board Battery Charger User Guide

Description

This PDF user guide is for the NOCO GENPRO10X2 On-Board Battery Charger.

About the Item

NOCO GENPRO10X2 2-Bank 12V 20-Amp On-Board Marine Battery Charger, Maintainer and Desulfator

UPC: 0-46221-19048-9

Meet the all-new GENPRO10X2. Similar to our GEN2, only better. It’s 19% smaller and delivers 33% more power. It’s one of the best performing onboard marine battery chargers we have ever made. A two-bank onboard battery charger rated at 20-amps (10-amps per bank) for 12-volt batteries, including marine, boat, starter, and deep-cycle batteries. Independently charge and control each battery bank with selectable charging modes – including 12V, 12V AGM, 12V Lithium, and 12V Repair Mode – for all types of lead-acid and lithium-ion batteries.

This User Guide contains important safety and operating instructions. Save these instructions.

(PDF) USER GUIDE (ENGLISH) (ESPAÑOL) (FRANÇAIS)

SUMMARY OF CONTENTS

– Important Safety Warnings
– How to use NOCO GENPRO10X2
– Charging Modes: Standby, 12V, 12V AGM, 12V LITHIUM, 12V REPAIR, Force Mode.
– Connecting to the Battery. Follow these steps when battery is installed in vehicle. Follow these steps when battery is outside vehicle.
– Begin Charging
– Auto-Memory
– Charging Times

– Understanding Charge LEDs:
25% Red LED – The 25% Charge LED will slowly pulse “on” and “off” when the battery is less than 25% charged. When the battery is 25% charged, the 25% LED will go solid and the next LED will begin to pulse.
50% Red LED – The 50% Charge LED will slowly pulse “on” and “off” when the battery is 25% – 50% charged. When the battery is 50% charged, the 50% LED will go solid and the next LED will begin to pulse.
75% Orange LED – The 75% Charge LED will slowly pulse “on” and “off” when the battery is 50% – 75% charged. When the battery is 75% charged, the 75% LED will go solid and the next LED will begin to pulse.
100% Green LED – The 100% Charge LED will slowly pulse “on” and “off”, when the battery is less than 100% fully charged. When the battery is fully charged, the Green LED will be solid, and the 25%, 50% and 75% Charge LEDs will turn “off”.
Maintenance Green LED – During Optimization, the 100% Charge LED will pulse “on” and “off” slowly. Once the battery is fully optimized the 100% Charge LED will turn solid green. The charger can be left connected to the battery indefinitely.

– Understanding Error LEDs:
Standby LED Solid – Charger is in Standby mode or Battery voltage is too low for charger to detect.
Overvoltage Error LED Solid – Battery voltage is too high for the selected charge mode. Check the battery and charge mode.
Bad Battery Error LED Solid – Possible battery short / Battery will not hold a charge. Have battery checked by a professional.
Reverse Polarity Error LED Solid – Reverse polarity. Reverse the battery connections.
Overvoltage Error LED, Bad Battery Error LED, Reverse Polarity Error LED Flashing – Charger internal temperature too high / Charger will resume function once the Charger internal temperature drops; Charger ambient temperature too cold / Charger will resume function once the Charger ambient temperature rises.

– Interface: Mode Button, Overvoltage Error LED, Bad Battery Error LED, Reverse Polarity Error LED, Standby LED, Charge LED, Mode LED, «Press and Hold» Mode LED.
– Technical Specifications
– Warranty

Why Download the Manual?

This user guide provides all the information from NOCO about the GENPRO10X2 On-Board Battery Charger, as detailed in the table of contents. Reading it completely will address most questions you might have. You can download and save it for offline use, including viewing it on your device or printing it for your convenience if you prefer a paper version.

How to Download the Manual?

Download it by clicking the button below

Download file

Helped you out?
Glad to hear that. It would be awesome if you could . . .